•  
    您好!歡迎來到我們的網站
    鎮江百靈船舶用品有限公司??
    24小時服務熱線:
    20年生產循環水處理
    0511-85728888
    為廣大用戶提供優質的產品和完善的服務
    Zhenjiang Bailing Ship Supplies Co., Ltd.?
    產品中心
    地址:鎮江市民營開發區
    公司網址:WWW.ZJBLCB.COM
    聯系電話:0511-85728888
    公司傳真:0511-85728028
    郵編:212111
    聯系我們
    你的當前位置為:
    919型消油劑(溢油分散劑)
        發布時間: 2019-08-05 09:32    


    使用說明

    919型消油劑(溢油分散劑)是處理消散流油品,處理環境污染的化學劑,配制方法獨特,注重于解除制品毒性和強化滲透,擴散能力以及對油品的乳化消散功能、脫油效應,并可防止溢油火災。
    特點
    1、處理的乳化能力強大,穩定性高,可生物降解性好;
    2、屬于”無毒類”產品,有利于保護水產資源;
    范圍
    1、處理海洋、港口、江湖河流等水面上的溢流石油污染。
    2、對煉油廠冷卻水和其它排放含油污水浮油的處理。
    3、用于油田排放水浮油的消散處理。
    4、用于港口岸壁、船塢、棧橋、船甲板、灘涂、內燃機等各種機械設備外體和油艙、油罐、油管內外壁的脫油清洗,尤其是小管徑油管的疏通。
    5、用以控制溢油事故的發生。
    方法
    1、處理水面溢油污染時,用噴灑器具盡量均勻的將本劑灑向浮油(液粒不宜過分霧化),停留15—40分鐘后,再經人工或機械(可用船艇航行)進行攪動,使本劑與溢油充分接觸、滲透和吸收,即可達到理想的處理效果。
    2、清洗機械等外體表面的聚積油時,噴灑本劑后,用工具刷動,再用凈水沖洗。
    3、用于油艙、油罐、油管內壁脫油時,使用壓力泵沖射,然后用水沖洗。當油層過厚,粘性較大時,選用適度的高壓泵操作??芍貜脱h沖洗,直到失去效力時,再換新劑。
    用量比例根據油的品種、厚度及風化程度而定。通常對于新興出的稀薄漬層,用量約為溢油的15-30%左右,油層較厚時應采取吸、刮和其它方法盡量回收。余下1mm左右時再施以本劑。遇有特殊情況,可繼續增加用量,但最多不能超過溢油的一倍以上。
    注意事項
    遠離火源,避免長時間爆曬、高溫烘烤和低溫冷凍。
    包裝
    20公升塑料桶
     


    919 Leakage Oil Disperser
    Usage
    919 Leakage Oil Disperser is a chemical agent which can be used to handle flowing oil product and environmental pollution. The confection method is unique, and the product is emphasizing on the removal of poison property, infiltration strengthening.diffusion capability, emulsification
    function of oil, dispersion effect of oil or grease, prevention of leakage oil fire.
    Characteristics :
    I . Strong emulsification, high stability, k good biological decomposability.
    2. It belongs to Non-poison product, avail to protect aquatic product resources.
    Applications
    1. handle the leakage petroleum pollution on the surface of sea. port, river or lake.
    2. Handle the floating oil of cooling water or other drain waste water in petroleum-refining factory.
    3. Handle the floating oil of drain waste water in oil field.
    4. clean the out-surfoce of mechanical equipments such as port bank wall. boatyard, trestle, deck of ship, beach, diesel. etc., and oil cabin, oil tank. oil pipeline especially for small
    size oil pipe.
    5. Control the happening of oil leakage accident.
    Using method
    1. Spray the product uniformly to the floating oil. After 15-40 min.. agitate by manual or machine to gain better effect.
    2. To clean the accumulating oil of the machinery surface use brush after spraying the agent, then wash with clean water.
    3. To clean the inner wall of oil cabinl. oil tank and oil pipe flush, with pressure Pump then wash with water. If the oil layer is too thick and the viscosity is too high flush with proper high pressure pump.
    Dosage
    The dosage is determined by the oil type. thickness or oil layer and airslake degree. For thin oil layer the dosage will be 15-30% of oil quantity. If the oil layer is too thick callback the
    oil to the best of one's abilities until the layer is about 1 mm. If encountering special condition may continue adding the agent with the max. dosage less than one times of leakage
    oil quantity.
    Attention
    Keep away from fire source. Avoid long time sunshine, also avoid to be baked at high temperature or frozen at low temperature.
    Packing
    Big size iron drum; 200 Liter
    Irom drum: 20 Liter
    亚洲国产精品久久艾草